Page 499 of 500

Re: What are you working on now?

Posted: September 30th, 2024, 5:20 pm
by Hidden Impact
sazabi2001 wrote:
geoffdragon wrote: September 30th, 2024, 7:56 am @sazabi2001..... lovely, what is that movement ( apart from an Angelus)
Angelus 215 movement, I think it’s the cheapest in-house chronograph movement from Angelus.
Ooooo, I see a Mare Nostrum in your future!


Sent from my iPhone using Tapatalk

Re: What are you working on now?

Posted: October 1st, 2024, 5:36 am
by wwwEvgeny
sazabi2001 wrote: September 30th, 2024, 9:16 am
wwwEvgeny wrote: September 30th, 2024, 5:42 am
sazabi2001 wrote: September 30th, 2024, 12:20 am Just finished.

Image

Image
Bravo! It is one of my favorite movements! did you install the pusher buttons yourself too?
No, the case is a 42mm Chinese quartz case comes with 2 buttons, and the stem height just right for this movement. But the buttons location is slightly off, so I had to modify the pin and make a larger cap to get the pin touching the pushers.

It’s a hardened stainless steel case, I have only basic hand tools so it’s very difficult to work on.
Its very brave and not cheap project. I like how you connected two such styles in a very brave way )) Angelus 215
. what is your next step? Rolex 618 or 633?
.

Re: What are you working on now?

Posted: October 1st, 2024, 11:42 am
by Pondoro
In my humble opinion, the soldered bars should have a tighter bend radius and be closer to the watch body.This would do two things for you , (1) Have a smaller more compact look on your wrist. Closer to the watch body with the bar pins less leverage thus stronger with added strength. When you made the bars, you should have laid them over each other to verify they were the same shape, (a mirror image of each other) .One looks like its 90 degrees on the bend , the other looks like 130 at the bend. The rest of the watch I like what you have done.

Re: What are you working on now?

Posted: October 1st, 2024, 4:37 pm
by Mellons
norskguru88 wrote: September 30th, 2024, 8:30 am A few custom dials I am working on ImageImageImageImage

Sent from my 23090RA98I using Tapatalk
Fantastic work!

Re: What are you working on now?

Posted: October 1st, 2024, 6:49 pm
by sazabi2001
Pondoro wrote: October 1st, 2024, 11:42 am In my humble opinion, the soldered bars should have a tighter bend radius and be closer to the watch body.This would do two things for you , (1) Have a smaller more compact look on your wrist. Closer to the watch body with the bar pins less leverage thus stronger with added strength. When you made the bars, you should have laid them over each other to verify they were the same shape, (a mirror image of each other) .One looks like its 90 degrees on the bend , the other looks like 130 at the bend. The rest of the watch I like what you have done.
I’m now waiting for parts to make a new strap. The lug/ shoulder bar is a brass wire welded onto the case and can be bent into shape. It looks that way now because it’s a 26mm lug size on a 20mm strap.The new strap in the right size should look a lot better.

Re: What are you working on now?

Posted: October 1st, 2024, 7:12 pm
by sazabi2001
Hidden Impact wrote: September 30th, 2024, 5:20 pm
sazabi2001 wrote:
geoffdragon wrote: September 30th, 2024, 7:56 am @sazabi2001..... lovely, what is that movement ( apart from an Angelus)
Angelus 215 movement, I think it’s the cheapest in-house chronograph movement from Angelus.
Ooooo, I see a Mare Nostrum in your future!


Sent from my iPhone using Tapatalk
The original plan was Mare Nostrum, but I figured it out a 52mm case is way too big for me. Also the cost of case would be too much for me as well.


I always want to try the Chinese 3646 chronograph case, personally I think it’s the best looking Pam shape and well suited for non-Pam dial. Also recently it has a 42mm quartz 3646 case, which is the perfect size on my wrist.

Another Chronograph with 42mm Chinese case, this one is the early version Valjoux 22 from 1915.

Image

Image

Image

Re: What are you working on now?

Posted: October 4th, 2024, 5:29 am
by NortON
20241004_121808.jpg
20241004_121318-01.jpeg
20241004_121837-01.jpeg

Re: What are you working on now?

Posted: October 4th, 2024, 5:32 am
by tafari
NortON wrote:
20241004_121808.jpg
20241004_121318-01.jpeg
20241004_121837-01.jpeg
very nice build D, love it that u use a sec hand

Re: What are you working on now?

Posted: October 4th, 2024, 5:36 am
by NortON
tafari wrote: October 4th, 2024, 5:32 am
NortON wrote:20241004_121808.jpg
20241004_121318-01.jpeg
20241004_121837-01.jpeg
very nice build D, love it that u use a sec hand
Thx K!
I didn't have a small second hand, maybe in the future I will fix this problem

Re: What are you working on now?

Posted: October 10th, 2024, 7:58 am
by NortON
20241010_155416.jpg