I like the crown from Athaya better
What are you working on now?
-
OnlineNortON
- Watch Savant
- Posts: 3625
- Joined: October 19th, 2018, 5:44 pm
-
5 year veteran
Frequent Flyer
Prolific poster
- wwwEvgeny
- Watch Addict
- Posts: 777
- Joined: November 20th, 2018, 1:54 am
-
5 year veteran
Frequent Flyer
Italiano addict
Oyster eater
Skillful builder
8 giorni nut
Good neighbour
Re: What are you working on now?
the dial is 2mm so need to mill down some space in the besel to fit thick besel
Sent from my SM-S9280 using Tapatalk
Sent from my SM-S9280 using Tapatalk
-
OnlineNortON
- Watch Savant
- Posts: 3625
- Joined: October 19th, 2018, 5:44 pm
-
5 year veteran
Frequent Flyer
Prolific poster
- wwwEvgeny
- Watch Addict
- Posts: 777
- Joined: November 20th, 2018, 1:54 am
-
5 year veteran
Frequent Flyer
Italiano addict
Oyster eater
Skillful builder
8 giorni nut
Good neighbour
Re: What are you working on now?
job done, now the dial fit good
Sent from my SM-S9280 using Tapatalk
Sent from my SM-S9280 using Tapatalk
-
- Super Lost Sheep
- Posts: 97
- Joined: November 28th, 2021, 3:42 pm
-
Frequent Flyer
Re: What are you working on now?
Just finished.
- wwwEvgeny
- Watch Addict
- Posts: 777
- Joined: November 20th, 2018, 1:54 am
-
5 year veteran
Frequent Flyer
Italiano addict
Oyster eater
Skillful builder
8 giorni nut
Good neighbour
Re: What are you working on now?
Bravo! It is one of my favorite movements! did you install the pusher buttons yourself too?
-
- Tinkerer
- Posts: 325
- Joined: May 17th, 2021, 9:05 am
-
Frequent Flyer
Re: What are you working on now?
@sazabi2001..... lovely, what is that movement ( apart from an Angelus)
-
- Sponsor
- Posts: 631
- Joined: April 11th, 2018, 2:16 pm
-
5 year veteran
Frequent Flyer
VIP
Sponsor
HF veteran
Dial master
Re: What are you working on now?
A few custom dials I am working on
Sent from my 23090RA98I using Tapatalk
Sent from my 23090RA98I using Tapatalk
-
- Super Lost Sheep
- Posts: 97
- Joined: November 28th, 2021, 3:42 pm
-
Frequent Flyer
Re: What are you working on now?
No, the case is a 42mm Chinese quartz case comes with 2 buttons, and the stem height just right for this movement. But the buttons location is slightly off, so I had to modify the pin and make a larger cap to get the pin touching the pushers.
It’s a hardened stainless steel case, I have only basic hand tools so it’s very difficult to work on.
-
- Super Lost Sheep
- Posts: 97
- Joined: November 28th, 2021, 3:42 pm
-
Frequent Flyer
Re: What are you working on now?
Angelus 215 movement, I think it’s the cheapest in-house chronograph movement from Angelus.geoffdragon wrote: ↑September 30th, 2024, 7:56 am @sazabi2001..... lovely, what is that movement ( apart from an Angelus)