Page 2 of 3
Re: Supplier for parts
Posted: March 31st, 2020, 4:29 pm
by Emilio
Oh, I get it. Sadly, I don't have any of those parts.
Re: Supplier for parts
Posted: March 31st, 2020, 4:46 pm
by Kp0y
Then you need to search a movement holder and bezel regarding your actual caseback because there are Athaya/EsDee/River (new 3646) 39.50mm OD and NW/River (old 3646) 38.80mm OD.
I have some movement holders and different bezels (Tall and Cali low)
Re: Supplier for parts
Posted: March 31st, 2020, 7:04 pm
by bmsm
I think the better option will be get case back, movement holder and bezel. It can be risky find something that fits and sending parts back and forward would cost more.
Maybe I'll talk with you [mention]Kp0y[/mention].
By the way, the plexi from the watch pictured above it has a crack, what measure should I take to get a replacement?
Re: Supplier for parts
Posted: March 31st, 2020, 7:11 pm
by jrlmsla
Was the broken plexi fit with a gasket or just pressed into the bezel? I typically skip the gasket and press fit. Using a little silicone to seal it up. The measurement you would need would just be the inner diameter of the bezel. Depending on the maker of the bezel you should be able to get a standard plexi from Gordon or others. For custom I make them a tiny bit too big then adjust down to perfect fit.
Re: Supplier for parts
Posted: March 31st, 2020, 7:20 pm
by bmsm
jrlmsla wrote: ↑March 31st, 2020, 7:11 pm
Was the broken plexi fit with a gasket or just pressed into the bezel? I typically skip the gasket and press fit. Using a little silicone to seal it up. The measurement you would need would just be the inner diameter of the bezel. Depending on the maker of the bezel you should be able to get a standard plexi from Gordon or others. For custom I make them a tiny bit too big then adjust down to perfect fit.
Unknown maker
It doesn't have a gasket I think it is just pressed into the bezel.
I'll check that tomorrow.
Thanks bro
Re: Supplier for parts
Posted: April 1st, 2020, 11:46 am
by bmsm
37.20mm the inner diameter
Re: Supplier for parts
Posted: April 1st, 2020, 12:19 pm
by jrlmsla
bmsm wrote:37.20mm the inner diameter
I can whip one up and send it to you to try.
Re: Supplier for parts
Posted: April 1st, 2020, 12:28 pm
by bmsm
jrlmsla wrote: ↑April 1st, 2020, 12:19 pm
bmsm wrote:37.20mm the inner diameter
I can whip one up and send it to you to try.
Thanks. I was checking at Gordon's site and he has plexi for that size and it's near me. If that doesn't fit or if I screw up the plexi I'll get back here
Re: Supplier for parts
Posted: April 1st, 2020, 1:09 pm
by jrlmsla
Sounds good
Re: Supplier for parts
Posted: April 1st, 2020, 2:58 pm
by Emilio
bmsm wrote: ↑April 1st, 2020, 12:28 pm
jrlmsla wrote: ↑April 1st, 2020, 12:19 pm
bmsm wrote:37.20mm the inner diameter
I can whip one up and send it to you to try.
Thanks. I was checking at Gordon's site and he has plexi for that size and it's near me. If that doesn't fit or if I screw up the plexi I'll get back here
Hey, I think I have one of those in that size too. Let me know if you need that.