I'm putting together a build list for a new project (two hander) and am planning on putting a hamilton in it.
There seems to be an impressive amount of 9xx models out there, are there any specific models I should be shopping for?
My limited research is leading me to believe a 917 would be a good choice. Really just looking for a rugged, reliable movement that can take a beating.
Hamilton Models
- unreformed66
- VIP
- Posts: 272
- Joined: April 11th, 2018, 4:16 pm
- Location: Ohio, United States
-
Frequent Flyer
VIP
HF veteran
Watchmaker
Re: Hamilton Models
The 917, 921,923 and 945 are all 10 size movements that have the Swiss style stem setup and are positive set. These will fit the standard cases that are available for the 917 movements. There are dozens of other Hamilton movements but they're all other sizes and negative set (the stem is part of the case not part of the movement) which are far more problematic to case. As for "rugged" you've got to understand that NONE of them have any shock protection. They were pocket watch movements and not meant to be made into wristwatches. Of course the vast majority of the wristwatches before the 1940s also had no shock protection but they also had smaller balances that weighed less and weren't as likely to break a balance staff pivot if they took a bump.
-
- Super Lost Sheep
- Posts: 31
- Joined: May 19th, 2018, 9:55 pm
Re: Hamilton Models
Thanks for the reply! The model numbers helped a lot. As for shock protection, in your experience has the lack of shock protection been a factor in standard everyday wear?unreformed66 wrote: ↑June 2nd, 2018, 7:38 pm As for "rugged" you've got to understand that NONE of them have any shock protection. They were pocket watch movements and not meant to be made into wristwatches.
- unreformed66
- VIP
- Posts: 272
- Joined: April 11th, 2018, 4:16 pm
- Location: Ohio, United States
-
Frequent Flyer
VIP
HF veteran
Watchmaker
Re: Hamilton Models
Not as long as you don't beat on them or drop them or otherwise mistreat them. And the good thing is that if worse comes to worst and you break a staff I can change one in about 20 minutes..lol. The later model Hamilton 10 size watches have a friction fit staff. You just remove the hairspring and roller table, drive out the old staff, drive in the new staff and replace the hairspring and roller table. They rarely require poising or any other work. Good stuff, far better than Corteberts or Molnijas.
- Yoda
- Honorary moderator
- Posts: 8080
- Joined: April 11th, 2018, 9:16 am
- Location: Stockholm
-
Mini Chat Squatter
Car lover
Bike lover
Knife maker
Animal
5 year veteran
Frequent Flyer
VIP
Prolific poster
HF veteran
Watchmaker
Good neighbour
Re: Hamilton Models
20 minutes, you need to practice more! LOL!
Average is 20 minutes, unless it took a hard blow.
I remember that Roland Murphy pointed out that fact as well. Good movements, but the 921 and 923 are the most beautiful movements of the four.
Average is 20 minutes, unless it took a hard blow.
I remember that Roland Murphy pointed out that fact as well. Good movements, but the 921 and 923 are the most beautiful movements of the four.
Enviado desde mi fucking Samsung S8.
- TimemiT
- Scoundrel
- Posts: 1292
- Joined: May 31st, 2018, 8:21 pm
- Location: Miami
-
Scoundrel
5 year veteran
Frequent Flyer
VIP
Prolific poster
HF veteran
8 giorni nut
Re: Hamilton Models
Great info guys ... I always enjoyed the look of hamilton's, especially the 921 and have a couple hoarded away .. Leewei style
Alpacalypse Now