Homage Forum

Emilio wrote:[mention]bmsm[/mention] looks like someone is making progress!

I was away from cad design for too long. A little bit rusty but I’ll get there

Trying to design the 3646 mid case but having hard time to make some curves and edges

bmsm wrote:

Emilio wrote:[mention]bmsm[/mention] looks like someone is making progress!

I was away from cad design for too long. A little bit rusty but I’ll get there

Trying to design the 3646 mid case but having hard time to make some curves and edges

I have an already design 3646 if you want it. (It would be cheating I guess )

Emilio wrote:

bmsm wrote:

Emilio wrote:[mention]bmsm[/mention] looks like someone is making progress!

I was away from cad design for too long. A little bit rusty but I’ll get there

Trying to design the 3646 mid case but having hard time to make some curves and edges

I have an already design 3646 if you want it. (It would be cheating I guess )

If you could share I would appreciate. It would be helpful to understand the angles and curves better. I’m using some blue prints shared by you here at HF

bmsm wrote:

Emilio wrote:

bmsm wrote: I was away from cad design for too long. A little bit rusty but I’ll get there

Trying to design the 3646 mid case but having hard time to make some curves and edges

I have an already design 3646 if you want it. (It would be cheating I guess )

If you could share I would appreciate. It would be helpful to understand the angles and curves better. I’m using some blue prints shared by you here at HF

Will do!

And a hint about the shape of the case: you can use the revolve option to create a solid from a sketch (section).

Emilio wrote:

bmsm wrote:

Emilio wrote:I have an already design 3646 if you want it. (It would be cheating I guess )

If you could share I would appreciate. It would be helpful to understand the angles and curves better. I’m using some blue prints shared by you here at HF

Will do!

And a hint about the shape of the case: you can use the revolve option to create a solid from a sketch (section).

That’s what I’m trying to do. At least going for the right direction

VanSong wrote:

earloflondon wrote:

VanSong wrote:Woohoo! I like . Plexi make by you?

Sent from my SM-N960F using Tapatalk

Yep, hand carved -literally- from an 8mm plexiglass blank

Sent from my SM-M205F using Tapatalk

Great work and achievement

Sent from my SM-N960F using Tapatalk

Thanks

Sent from my SM-M205F using Tapatalk

Emilio wrote:

bmsm wrote:

Emilio wrote:I have an already design 3646 if you want it. (It would be cheating I guess )

If you could share I would appreciate. It would be helpful to understand the angles and curves better. I’m using some blue prints shared by you here at HF

Will do!

And a hint about the shape of the case: you can use the revolve option to create a solid from a sketch (section).

Is it possible to get files of 3646 case?

Sent from my ELE-L29 using Tapatalk

NortON wrote: ↑March 29th, 2020, 5:22 pm 20200330_010821-01.jpeg

You managed to put the Moli back so soon ? Impressive !

Alou wrote: ↑March 30th, 2020, 9:52 am

NortON wrote: ↑March 29th, 2020, 5:22 pm 20200330_010821-01.jpeg

You managed to put the Moli back so soon ? Impressive !

Thanks! It took a few hours and it wasn't easy, the first time)))
The mouvement has the same problems, but now it's clean but not lubricated, oil is still on the way...

NortON wrote:

Alou wrote: ↑March 30th, 2020, 9:52 am

NortON wrote: ↑March 29th, 2020, 5:22 pm 20200330_010821-01.jpeg

You managed to put the Moli back so soon ? Impressive !

Thanks! It took a few hours and it wasn't easy, the first time)))
The mouvement has the same problems, but now it's clean but not lubricated, oil is still on the way...

good job, what are the problems?