Page 8 of 11
Re: Any watches and those unfinished with Oyang case sets
Posted: November 10th, 2020, 2:11 am
by Yoda
earloflondon wrote: ↑November 10th, 2020, 2:02 am
Yoda wrote:I still have my Oyang case unfinished, haven't been able to find a machine shop which can create the hole in the massive threaded brass piece, not formed and soldered the wire lugs either.
And you promised pics, I still remember maester,
Sent from my SM-M205F using Tapatalk
I know, but I am stuck with the brass block.
Re: Any watches and those unfinished with Oyang case sets
Posted: November 10th, 2020, 5:02 am
by earloflondon
Yoda wrote:earloflondon wrote: ↑November 10th, 2020, 2:02 am
Yoda wrote:I still have have my Oyang case unfinished, haven't been able to find a machine shop which can create the hole in the massive threaded brass piece, not formed and soldered the wire lugs either.
And you promised pics, I still remember maester,
Sent from my SM-M205F using Tapatalk
I know, but I am stuck with the brass block.
Just send whatever you have. Even the parts are exciting
Sent from my SM-M205F using Tapatalk
Re: Any watches and those unfinished with Oyang case sets
Posted: November 10th, 2020, 4:29 pm
by Yoda
earloflondon wrote: ↑November 10th, 2020, 5:02 am
Yoda wrote:earloflondon wrote: ↑November 10th, 2020, 2:02 am
And you promised pics, I still remember maester,
Sent from my SM-M205F using Tapatalk
I know, but I am stuck with the brass block.
Just send whatever you have. Even the parts are exciting
Sent from my SM-M205F using Tapatalk
Ok, I will dig it out tomorrow then....
Re: Any watches and those unfinished with Oyang case sets
Posted: November 11th, 2020, 12:41 am
by earloflondon
Thus far only 1 3646 and 3 6154s were revealed. We know there are some 15 of each out there
Sent from my SM-M205F using Tapatalk
Re: Any watches and those unfinished with Oyang case sets
Posted: November 11th, 2020, 3:45 am
by Yoda
20201111_102540_resized.jpg
20201111_102555_resized.jpg
20201111_102607_resized.jpg
20201111_102630_resized.jpg
Re: Any watches and those unfinished with Oyang case sets
Posted: November 11th, 2020, 4:09 am
by tafari
Yoda wrote:20201111_102540_resized.jpg
20201111_102555_resized.jpg
20201111_102607_resized.jpg
20201111_102630_resized.jpg
nice case, the other case, is it 6154 or 6152 no cg?
Re: Any watches and those unfinished with Oyang case sets
Posted: November 11th, 2020, 4:23 am
by Yoda
tafari wrote: ↑November 11th, 2020, 4:09 am
Yoda wrote:20201111_102540_resized.jpg20201111_102555_resized.jpg20201111_102607_resized.jpg20201111_102630_resized.jpg
nice case, the other case, is it 6154 or 6152 no cg?
Davdew case.
Re: Any watches and those unfinished with Oyang case sets
Posted: November 11th, 2020, 4:34 am
by tafari
Yoda wrote:tafari wrote: ↑November 11th, 2020, 4:09 am
Yoda wrote:20201111_102540_resized.jpg20201111_102555_resized.jpg20201111_102607_resized.jpg20201111_102630_resized.jpg
nice case, the other case, is it 6154 or 6152 no cg?
Davdew case.
thx , I missed that one great case
Re: Any watches and those unfinished with Oyang case sets
Posted: November 11th, 2020, 10:14 am
by Yoda
I wonder how to proceed with the massive threaded brass lump.....
It is already threaded and how to make it a useable movement ring without messing up the threads.
Anyone out there who has/had this problem?
It would be great to hear the solution.
Re: Any watches and those unfinished with Oyang case sets
Posted: November 11th, 2020, 10:29 am
by tafari
Yoda wrote:I wonder how to proceed with the massive threaded brass lump.....
It is already threaded and how to make it a useable movement ring without messing up the threads.
Anyone out there who has/had this problem?
It would be great to hear the solution.
that’s a good question, I never did it. but I would build a opposite part where to screw the brass lump inside and than use a lathe. you could use a short metal pipe give it a inside thread like the same as the brass lump