Homage Forum

Today, a conversion from alarm to non alarm and non incabloc to incabloc. Not completely finished yet, waiting for the winding wheel.

The other one was just a simple conversion and service.

Yoda wrote:Today, a conversion from alarm to non alarm and non incabloc to incabloc. Not completely finished yet, waiting for the winding wheel.

The other one was just a simple conversion and service.

20190724_155634_resized_1.jpg

the one in the middle is amazing

tafari wrote: ↑July 24th, 2019, 9:46 am

Yoda wrote:Today, a conversion from alarm to non alarm and non incabloc to incabloc. Not completely finished yet, waiting for the winding wheel.

The other one was just a simple conversion and service.

20190724_155634_resized_1.jpg

the one in the middle is amazing

The one in the middle started out as a non incabloc SW alarm movement, so I converted to incabloc as well.
The barrel bridge was an unfinished prototype and there was no hole for the setting lever screw and the hole for the center wheel was only drilled to 0,25 mm.

Yoda wrote:

tafari wrote: ↑July 24th, 2019, 9:46 am

Yoda wrote:Today, a conversion from alarm to non alarm and non incabloc to incabloc. Not completely finished yet, waiting for the winding wheel.

The other one was just a simple conversion and service.

20190724_155634_resized_1.jpg

the one in the middle is amazing

The one in the middle started out as a non incabloc SW alarm movement, so I converted to incabloc as well.
The barrel bridge was an unfinished prototype and there was no hole for the setting lever screw and the hole for the center wheel was only drilled to 0,25 mm.

a very good work M., any plan for a build?

tafari wrote: ↑July 24th, 2019, 12:06 pm

Yoda wrote:

tafari wrote: ↑July 24th, 2019, 9:46 am
the one in the middle is amazing

The one in the middle started out as a non incabloc SW alarm movement, so I converted to incabloc as well.
The barrel bridge was an unfinished prototype and there was no hole for the setting lever screw and the hole for the center wheel was only drilled to 0,25 mm.

a very good work M., any plan for a build?

The one in the middle ended up being an extensive work
(my idea), it is a work for a member here and I hope that the alarm movement will be sold to the interested party I have discussed the details with for a while.

The last one is a project, but it will be a full blown SW incabloc rebuilt with gen parts soon. I hope that it will finish the WL I broke down in pieces and sold to pay for medical reasons.

Yoda wrote:

tafari wrote: ↑July 24th, 2019, 12:06 pm

Yoda wrote:
The one in the middle started out as a non incabloc SW alarm movement, so I converted to incabloc as well.
The barrel bridge was an unfinished prototype and there was no hole for the setting lever screw and the hole for the center wheel was only drilled to 0,25 mm.

a very good work M., any plan for a build?

The one in the middle is a work for a member here and I hope that the one to the right will be sold to the interested party I discussed the details with.

The last one is a project, but it will be a full blown SW incabloc rebuilt with gen parts soon.

all the to are nice ones, waiting for the 3. with gen parts to see I guess it will be a beauty too

I aim for a very special build this time, the keeper.

Yoda wrote:I aim for a very special build this time, the keeper.

I can’t wait to see the pics!

Another mm build, this time stainless steel.

Latest project before dial and hands changes, after gasket changes and crown gasket mod, crown reshape. Cg pin also slightly worked

and the bracelet is a beauty!

mellons wrote: ↑July 25th, 2019, 6:53 am Another mm build, this time stainless steel.

Latest project before dial and hands changes, after gasket changes and crown gasket mod, crown reshape. Cg pin also slightly worked