Page 55 of 525

Re: What are you working on now?

Posted: January 30th, 2020, 6:27 pm
by Emilio
Erick510 wrote:Journey esdee welded lug Dave dial I did some lume work ImageImageImageImage

Sent from my SM-N970U using Tapatalk
Nice!

Re: What are you working on now?

Posted: January 30th, 2020, 11:58 pm
by VanSong
Emilio wrote:
Erick510 wrote:Journey esdee welded lug Dave dial I did some lume work ImageImageImageImage

Sent from my SM-N970U using Tapatalk
Nice!
+1, beautiful indeed.

Sent from my SM-N960F using Tapatalk


Re: What are you working on now?

Posted: January 31st, 2020, 12:15 am
by VanSong
Finally got sometimes on this CNY break. Am trying to modded the tall tubes to my originally aged Angelus style hands which I think it sits too flush to the dial. Have brought an Athaya tall tubes pencil hands as donors!

But upon opening up the watch, I found myself looses the parts 3 times!Image Am luck that I managed to recover them back after some searchingImage. I even had to search YouTube for answer to see how the setting lever was being installed in the first place after it went loose! And yes, this is challenging for a Newbies like me but it was a great experience ImageImageImageImageImage

Sent from my SM-N960F using Tapatalk


Re: What are you working on now?

Posted: January 31st, 2020, 2:50 am
by tafari
VanSong wrote:Finally got sometimes on this CNY break. Am trying to modded the tall tubes to my originally aged Angelus style hands which I think it sits too flush to the dial. Have brought an Athaya tall tubes pencil hands as donors!

But upon opening up the watch, I found myself looses the parts 3 times!Image Am luck that I managed to recover them back after some searchingImage. I even had to search YouTube for answer to see how the setting lever was being installed in the first place after it went loose! And yes, this is challenging for a Newbies like me but it was a great experience ImageImageImageImageImage

Sent from my SM-N960F using Tapatalk
good job, I remember how often I was searching for parts Image

Re: What are you working on now?

Posted: January 31st, 2020, 5:23 am
by Sevanata
blueradish wrote:SF240 to DSN Egi movement ring back from NZ, so this guy is back in action as soon as I'm healed

Image
I see death people Image

Sent from my VOG-L29 using Tapatalk


Re: What are you working on now?

Posted: January 31st, 2020, 5:36 am
by Sevanata
tafari wrote:
Belkin12 wrote:Did you solder the bezel and the midcase from inside?
Im using a solder paste.it is extra for va steel soldering wtih other materials like brass.Im using the solder wire from the same brand for it. the stem tube I solder from the outside and the bezel from the inside.
the paste is very good for soldering, because it already includes solder wire and when you heat the case you see the solder paste comes silver shining and you just hold the solder wire to the soldering part. the solder paste take the melded wire inside the soldering part,so it runs everywhere.
it makes the soldering very easy
Where to get that soldering paste kit Tafari? Would like to try it out. Thanks.

Sent from my VOG-L29 using Tapatalk


Re: What are you working on now?

Posted: January 31st, 2020, 5:43 am
by tafari
Sevanata wrote:
tafari wrote:
Belkin12 wrote:Did you solder the bezel and the midcase from inside?
Im using a solder paste.it is extra for va steel soldering wtih other materials like brass.Im using the solder wire from the same brand for it. the stem tube I solder from the outside and the bezel from the inside.
the paste is very good for soldering, because it already includes solder wire and when you heat the case you see the solder paste comes silver shining and you just hold the solder wire to the soldering part. the solder paste take the melded wire inside the soldering part,so it runs everywhere.
it makes the soldering very easy
Where to get that soldering paste kit Tafari? Would like to try it out. Thanks.

Sent from my VOG-L29 using Tapatalk
here is where I bought it

https://www.sonderlote.de/epages/621734 ... 12-0001%22

Re: What are you working on now?

Posted: January 31st, 2020, 6:48 am
by Emilio
3D printing a lume holder for NW dial (bottom layer)
For [mention]tafari[/mention]


Image

Image

Re: What are you working on now?

Posted: January 31st, 2020, 6:50 am
by tafari
Emilio wrote:3D printing a lume holder for NW dial (bottom layer)
For [mention]tafari[/mention]


Image

Image
wow it looks fantastic Emilio Image

Re: What are you working on now?

Posted: January 31st, 2020, 6:53 am
by Emilio
tafari wrote:
Emilio wrote:3D printing a lume holder for NW dial (bottom layer)
For [mention]tafari[/mention]


Image

Image
wow it looks fantastic Emilio Image
Hope it fits (you can always sand it down a bit)