Page 532 of 533

Re: What are you working on now?

Posted: October 27th, 2025, 8:47 am
by dj57
wwwEvgeny wrote:
dj57 wrote:
wwwEvgeny wrote:was working on CG and Crown...Image

Sent from my SM-S9380 using Tapatalk
Great build ImageImage
Thank you! it's a first stage tuning Image only. tomorrow will put on the strap, some minor fixing. and can ware it. Next stage is display case back as the engravings are from gmt pam Image, will replace them with dome decorations

Sent from my SM-S9380 using Tapatalk
Hi,
Could you please provide some pieces of information regarding parts etc?
Or did a miss something? Image

Re: What are you working on now?

Posted: October 27th, 2025, 9:26 am
by Elias Livadaris
Exceptional job whicj reflects the love for the hobby!!!

Re: What are you working on now?

Posted: October 27th, 2025, 9:27 am
by Elias Livadaris
Detailing and craftsmanship in full reveal!!!!

Re: What are you working on now?

Posted: October 28th, 2025, 11:22 pm
by wwwEvgeny
@Elias Livadaris @dj57 @NortON thank you very much for encouraging words. Regarding the parts. On thread EBAY auctions, there appeared a link for disassembled 00140 golden PAM. it was not cheap, but usually one batch is 200 pieces, so I decided to build nice Top tuning piece. As the whole watch go up to 25k usd. in over polished condition is 15k. I bargain a bit and took the movement with dial. the pictures were not clear so there were a risk. Anyway the price was ok for only dial and movement set. I started to look for 4A rep of any old PAM with automatic 7750 with the lens on the glass. bought through local reseller. Still a lot work need to be done. reduced the gap between CG and lever. retouched the surfaces. Adding the washer between the dial and bezel. made the new sit for movement and 3 slots for holding screws. the crown was over polished for my taste, so I made it more sharp. as the movement is nicely decorated, I will make display case back with same engravings as on 180, but with decoration. Thank you very much.Image

Sent from my SM-S9380 using Tapatalk

Re: What are you working on now?

Posted: October 29th, 2025, 6:37 am
by NortON
Ali Pre V case
20251029_103205.jpg
20251029_103052.jpg

Re: What are you working on now?

Posted: October 31st, 2025, 12:41 am
by Ebzen02
NortON wrote:Ali Pre V case
20251029_103205.jpg
20251029_103052.jpg
How’s that CG?


Sent from my iPhone using Tapatalk

Re: What are you working on now?

Posted: October 31st, 2025, 6:47 am
by NortON
Ebzen02 wrote: October 31st, 2025, 12:41 am
NortON wrote:Ali Pre V case
20251029_103205.jpg
20251029_103052.jpg
How’s that CG?


Sent from my iPhone using Tapatalk
Apparently this is a copy of DSN, the quality is slightly inferior
20251031_133003.jpg
20251031_133121.jpg
CB from @Kp0y Thx A! ;)
20251031_133634.jpg

Re: What are you working on now?

Posted: October 31st, 2025, 7:32 am
by Ebzen02
NortON wrote:
Ebzen02 wrote: October 31st, 2025, 12:41 am
NortON wrote:Ali Pre V case
20251029_103205.jpg
20251029_103052.jpg
How’s that CG?


Sent from my iPhone using Tapatalk
Apparently this is a copy of DSN, the quality is slightly inferior
20251031_133003.jpg
20251031_133121.jpg
CB from [smention u=49]Kp0y[/smention] Thx A! ;)
20251031_133634.jpg
Doesn’t seem that bad at all.. just a little work needed.


Sent from my iPhone using Tapatalk

Re: What are you working on now?

Posted: November 12th, 2025, 3:20 am
by dj57
This is my very lastMoonswatch in metal case mod; no further ones will follow.
Image

Re: What are you working on now?

Posted: November 19th, 2025, 9:21 am
by dj57
Image

—> mancino vs destrorso (destro) <—

Just two simple 44mm builds with Helenarou dials and hands. Silicone straps, ST36 and cases from AliE. Image
Ordered by friends of mine.