What are you working on now?

[erlendh]

Oysterquartz 17014 case with LeCoultre «tiger eye» dial. Not sure what movement to put in. Need ca. 2.0mm stem height. 1.8mm should work too.

[wwwEvgeny]

before vacation, afraid will not finish

Sent from my SM-S9280 using Tapatalk

[south105323]

Custom hands. First stage is to polish them in place on the sheet. Easier and safer than doing it individually.



Broached out the hole, tight fit for a short section of brass tube, which I’ll broach the inside to fit the pinion.
(Don’t mind the rough end, will be sanded down to correct height. All hand tools only, cutting broaches, files, sandpaper. Dremel for polishing. Wish I had a lathe to play with)




Soldered, just need to clean, file off the tab and give it a final polish, then lume.

[bmsm]

Custom hands. First stage is to polish them in place on the sheet. Easier and safer than doing it individually.



Broached out the hole, tight fit for a short section of brass tube, which I’ll broach the inside to fit the pinion.
(Don’t mind the rough end, will be sanded down to correct height. All hand tools only, cutting broaches, files, sandpaper. Dremel for polishing. Wish I had a lathe to play with)




Soldered, just need to clean, file off the tab and give it a final polish, then lume.

Great job. What laser did you use to cut the hands?


Sent from my iPad using Tapatalk

[south105323]

Custom hands. First stage is to polish them in place on the sheet. Easier and safer than doing it individually.



Broached out the hole, tight fit for a short section of brass tube, which I’ll broach the inside to fit the pinion.
(Don’t mind the rough end, will be sanded down to correct height. All hand tools only, cutting broaches, files, sandpaper. Dremel for polishing. Wish I had a lathe to play with)




Soldered, just need to clean, file off the tab and give it a final polish, then lume.

Great job. What laser did you use to cut the hands?


Sent from my iPad using Tapatalk

Fiber. 0.25mm brass. Not sure on settings. He is actually on here. John, Ard Laser

[bmsm]

Custom hands. First stage is to polish them in place on the sheet. Easier and safer than doing it individually.



Broached out the hole, tight fit for a short section of brass tube, which I’ll broach the inside to fit the pinion.
(Don’t mind the rough end, will be sanded down to correct height. All hand tools only, cutting broaches, files, sandpaper. Dremel for polishing. Wish I had a lathe to play with)




Soldered, just need to clean, file off the tab and give it a final polish, then lume.

Great job. What laser did you use to cut the hands?


Sent from my iPad using Tapatalk

Fiber. 0.25mm brass. Not sure on settings. He is actually on here. John, Ard Laser

Sent from my iPad using Tapatalk

[wwwEvgeny]

Custom hands. First stage is to polish them in place on the sheet. Easier and safer than doing it individually.



Broached out the hole, tight fit for a short section of brass tube, which I’ll broach the inside to fit the pinion.
(Don’t mind the rough end, will be sanded down to correct height. All hand tools only, cutting broaches, files, sandpaper. Dremel for polishing. Wish I had a lathe to play with)




Soldered, just need to clean, file off the tab and give it a final polish, then lume.

nice GMT style Alarm hand! ️ you go for seconds hand, I can see, I desided to leave it blank , but who knows, I left a hole , so can add later

nice project, nice inspiration

Sent from my SM-S9280 using Tapatalk

[south105323]

Custom hands. First stage is to polish them in place on the sheet. Easier and safer than doing it individually.



Broached out the hole, tight fit for a short section of brass tube, which I’ll broach the inside to fit the pinion.
(Don’t mind the rough end, will be sanded down to correct height. All hand tools only, cutting broaches, files, sandpaper. Dremel for polishing. Wish I had a lathe to play with)




Soldered, just need to clean, file off the tab and give it a final polish, then lume.

nice GMT style Alarm hand! ️ you go for seconds hand, I can see, I desided to leave it blank , but who knows, I left a hole , so can add later

nice project, nice inspiration

Sent from my SM-S9280 using Tapatalk

Yes, I wasn’t happy with what I could get for the alarm hand, was using a Rolex GMT hand but it was too long. I am painting the arm of the hand black, I just want the triangle pointing at the indices without covering them. I was debating seconds hand also, but decided to make one.

[NortON]

just for fun

20240731_185910.jpg

[dj57]

just for fun

20240731_185910.jpg

Nice
Me too

One case, one movement, many choices.