Homage Forum

Posted: **April 20th, 2022, 9:35 am**

Denis wrote: ↑April 19th, 2022, 1:52 pm
Kkstraps wrote: ↑April 17th, 2022, 2:22 pm 26mm

Great work

Thanks looks better with strap

Posted: **April 20th, 2022, 9:41 am**

Mike08 wrote: ↑April 20th, 2022, 8:55 am Resin filling

20220420_155449.jpg

Great work M!

Posted: **April 20th, 2022, 11:31 am**

Kkstraps wrote:
Denis wrote: ↑April 19th, 2022, 1:52 pm
Kkstraps wrote: ↑April 17th, 2022, 2:22 pm 26mm

Great work

Thanks looks better with strap
Very clean patina. Nice Job

Posted: **April 20th, 2022, 11:33 am**

Nottingham wrote: ↑April 20th, 2022, 11:31 am
Kkstraps wrote:
Denis wrote: ↑April 19th, 2022, 1:52 pm

Thanks looks better with strap
Very clean patina. Nice Job
+1 Awesome strap

Posted: **April 20th, 2022, 12:36 pm**

@Nottingham, @NortON
Thanks guys

Posted: **April 21st, 2022, 5:23 am**

wwwEvgeny wrote:
Tanukjaju wrote:
wwwEvgeny wrote: ↑April 6th, 2022, 8:12 am removed the SS triangle with lume dot, replaced it with yellow and bigger one. made the besel more crisp, as the surface near triangle was soapy or battered....

Sent from my SM-S9080 using Tapatalk
18K! Very nice touch. Is that laser engraved?
yes, but I was thinking to mill it... not in this case.. laser was ok... not sure if can finish tomorrow two dials, gray is ready without lume, dark brown almost, not sure if I will continue to play with color...

Sent from my SM-S9080 using Tapatalk

to be continued ....

Sent from my SM-S9080 using Tapatalk

Posted: **April 21st, 2022, 5:41 am**

Mike08 wrote: ↑April 20th, 2022, 8:55 am Resin filling

20220420_155449.jpg

Very clean borders! My first time was not successful

have to remove… second.. didn’t try yet..

Good clean work

Posted: **April 21st, 2022, 5:48 am**

wwwEvgeny wrote: ↑April 21st, 2022, 5:41 am
Mike08 wrote: ↑April 20th, 2022, 8:55 am Resin filling

20220420_155449.jpg
Very clean borders! My first time was not successful have to remove… second.. didn’t try yet..

Good clean work

thank you buddy

The key is UV-resin!
For 1 piece dials no problem because you can sand the residue away...
with 3 piece dials it´s a little bit more complicated because you need to work very accurate and the thin uv-resin doesn´t like to stay in the indices if thinly applied... you need some trials and the right tool...

Posted: **April 21st, 2022, 7:56 am**

wwwEvgeny wrote: ↑April 21st, 2022, 5:23 am
wwwEvgeny wrote:
Tanukjaju wrote:
18K! Very nice touch. Is that laser engraved?
yes, but I was thinking to mill it... not in this case.. laser was ok... not sure if can finish tomorrow two dials, gray is ready without lume, dark brown almost, not sure if I will continue to play with color...

Sent from my SM-S9080 using Tapatalk
to be continued ....

Sent from my SM-S9080 using Tapatalk

Popcorn time

Posted: **April 21st, 2022, 8:13 am**

wwwEvgeny wrote: ↑April 21st, 2022, 5:23 am
wwwEvgeny wrote:
Tanukjaju wrote:
18K! Very nice touch. Is that laser engraved?
yes, but I was thinking to mill it... not in this case.. laser was ok... not sure if can finish tomorrow two dials, gray is ready without lume, dark brown almost, not sure if I will continue to play with color...

Sent from my SM-S9080 using Tapatalk
to be continued ....

Sent from my SM-S9080 using Tapatalk

Outstanding!

Homage Forum

What are you working on now?

Re: What are you working on now?

Re: What are you working on now?

Re: What are you working on now?

Re: What are you working on now?

Re: What are you working on now?

Re: What are you working on now?

Re: What are you working on now?

Re: What are you working on now?

Re: What are you working on now?

Re: What are you working on now?